The gallery

Examples, Jigs and assemblies

Every model here comes with its file. Download it and open it in 3DCraft: File › Open…, or double-click the file once 3DCraft is installed.

Examples26 Jigs33 Assemblies6

Examples

26 models

Parts and products, from a screw to a moka pot. Each is a 3DCraft document: a .3dcraft file with its history, variables and checks.

Machine building

Socket head cap screw

An ISO 4762 socket head cap screw, M3 to M12 in the standard's lengths, with a rolled thread, in black-oxide steel.

Download.3dcraft · 57 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Machine building

T-slot aluminium profile

A 30 x 30 mm B-type aluminium profile with four 8 mm T-slots and a core bore tapped M8 at both ends, cut to length, in clear anodised EN AW-6063.

Download.3dcraft · 69 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Laser cutting, art

A Ø 300 mm wall clock laser cut and engraved from 6 mm birch plywood for a quartz sweep movement, Roman or Arabic numerals, a laminated keyhole hanger and foot at the back and black hands set to the time.

Download.3dcraft · 460 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Woodturning

Turned walnut bowl

A face-grain serving bowl turned from a 10 × 4 inch walnut blank: an even 7 mm wall from a rounded rim to a foot ring with a dovetailed chuck recess, with its capacity in millilitres.

Download.3dcraft · 50 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

3D printing

Hex key stand

A stepped desk stand for a metric hex key set to ISO 2936, 1.5 to 10 mm, printed in PLA without supports, sizes embossed in black.

Download.3dcraft · 471 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Sheet metal

Steel bookend

A bookend laser cut from 2 mm DC01 cold-rolled steel with an ogee-arch window, bent once on a press brake and powder coated deep teal.

Download.3dcraft · 46 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Toolmaking

V-block pair with clamps

A matched pair of hardened and ground 90° V-blocks, 45 × 40 × 35 mm, for shafts of 6 to 30 mm, with black-oxide U-clamps holding a ground test pin.

Download.3dcraft · 162 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Sheet metal, HVAC

Square-to-round transition

A four-piece transition from a 400 x 300 mm rectangular duct to a 250 mm round duct in 0.8 mm galvanised steel: flat triangles and developable cone corners with straight ends, one piece unfolded into the flat pattern cut four times, with a lapped collar, a P20 angle frame and a sealed spigot.

Download.3dcraft · 123 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Packaging

Mailer box

A FEFCO 0427 mailer of single-wall E-flute kraft board, 200 × 150 × 60 mm inside, folded from its die-cut blank: rolled end walls locked by tabs, dust flaps and a tuck-in lid.

Download.3dcraft · 140 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

3D printing, product design

Headphone stand

A one-piece headphone stand printed upright in PETG without supports: a slim lofted column flaring into a wide saddle curved like a headband, a swept cable hook, and a round base weighted by an embedded steel disc.

Download.3dcraft · 119 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Woodworking

Splayed-leg stool

An oak sitting stool, Ø 340 mm seat at 450 mm, on four legs splayed and raked 10°, tenoned through the seat and wedged with walnut, with two shouldered side stretchers; proven in closed form and against the stool stability test of IS 5416-2.

Download.3dcraft · 83 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

CNC, RC

5-inch FPV drone frame

A true-X freestyle quadcopter frame for 5 to 5.3 inch props, CNC routed from 2 mm and 5 mm carbon fibre sheet, with purple anodised standoffs, a 30.5 mm stack, a cage for a 19 mm camera and real 5.1 x 4.3 x 3 props lofted at their pitch.

Download.3dcraft · 288 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Machine building

Cast handwheel

A DIN 950 spoked handwheel in grey cast iron, 80 to 500 mm, with cranked oval spokes, a turned and polished rim, a keyed bore and a DIN 98 revolving handle on a boss at the standard's radius, painted machine green.

Download.3dcraft · 122 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Jewellery

Solitaire ring

An 18 ct yellow-gold solitaire in ISO 8653 ring sizes 44 to 72: a comfort-fit court shank and a four-prong basket head holding a round brilliant of 0.25 to 2 ct, cut to Tolkowsky's proportions and sized from its weight.

Download.3dcraft · 87 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Hydraulics

Hydraulic cylinder

A double-acting ISO 6020-2 tie-rod cylinder, bore 40, rod 28, with clevises at both ends, a rod that moves with a parameter and a cutaway that shows the piston, the seals and the gland.

Download.3dcraft · 255 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Architecture, steel construction

Spiral staircase

A steel spiral staircase with oak treads, Ø 1600 mm and 2800 mm floor to floor, on a Ø 114.3 mm column, with a helical handrail and a landing, checked against DIN 18065.

Download.3dcraft · 185 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Marine

Ship propeller

A four-blade Wageningen B4-55 ship propeller, Ø 600 mm, pitch ratio 0.8, 15° rake, its blades from the series' published tables, in polished nickel-aluminium bronze.

Download.3dcraft · 258 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Lutherie

Electric guitar body

An original double-cutaway solid body in red alder with a carved top, a bolt-on neck pocket, two humbucker routes, a rear control cavity and a string-through bridge placed by the scale length, finished in candy-apple red.

Download.3dcraft · 486 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Naval design

RC yacht hull

An International One Metre radio-sailing yacht to the IOM Class Rules 2026: a glass hull lofted from a table of stations with a painted deck, a tapered carbon fin, a lead bulb sized by its mass and a carbon rudder, floated at the class's 4 kg in fresh water.

Download.3dcraft · 146 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Product design

Moka pot

An original twelve-sided stovetop espresso maker in cast aluminium for 3, 4 or 6 cups, sized by its physics: the safety valve sits where the water for the cups ends, the funnel holds the coffee for that water, the lid opens on a working hinge, and the pot stands on a 10° slope full or empty.

Download.3dcraft · 249 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Topography, art

Mont Ventoux relief

Mont Ventoux and the Bédoin climb of the Tour de France Femmes 2026 (stage 7) at 1:70 000: a relief printed in forest green and limestone white with brass kilometre pins and the summit tower on a walnut base, or laser-cut contour layers.

Download.3dcraft · 888 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

CNC, furniture

Flat-pack bookcase

An open bookcase of 18 mm birch plywood, CNC-routed from one 2500 x 1250 mm sheet and put together without screws, glue or tools: shelves and back rails pass through the sides in tusk tenons locked by tapered wedges.

Download.3dcraft · 238 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Injection moulding

Snap-fit enclosure

An injection-moulded enclosure for a 100 x 70 mm circuit board: a matt white ABS base and a translucent smoke-grey polycarbonate lid, closed by four external U-shaped snap latches, both parts moulded in straight-pull tools without slides.

Download.3dcraft · 207 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Steel construction, welding

Welded tube truss

An original 6 m Warren truss of EN 10219-2 circular hollow sections in S355J2H, with gap K-joints to EN 1993-1-8, coped diagonals fillet-welded all round and end plates, in red-oxide primer.

Download.3dcraft · 98 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Laser cutting, art

Layered cardboard rhino

An original stylised rhinoceros, 300 mm from rump to lip, laser-cut from white-faced corrugated board in 30 straight-walled layers of its sections; each layer but the middle pair goes onto its neighbour's engraved outline.

Download.3dcraft · 384 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Woodworking

Skateboard deck and press mould

An original 8.0 x 31.75 in street deck of seven 1/16 in hard-maple plies with a dyed core, radial concave and 20 degree kicks, cut and drilled from the pressed stack, with the two MDF halves of its press mould.

Download.3dcraft · 133 kB Open in the browser (opens in a new tab)How it was made

Licence: MIT

Jigs

33 models

A Jig is a finished design with a form: the sizes that matter are fields, the rest follows by formulas, and every result is checked. No AI needed.

Woodwork, garden birds

Nest box from one plank

A nest box for a garden bird of the Low Countries, sawn from one plank and screwed: pick the species and the entrance, floor, height and even the shape of the box follow Vogelbescherming Nederland's table.

Download.3dcraftjig · 169 kB Open in the browser (opens in a new tab)How it was made